FlowsBook a callSign inCreate free accountSign up
AI employees and automation

An AI agent for nonprofits: service gaps, partner sites and collection rounds

How an AI agent for nonprofits finds neighborhoods far from a service, lists shops and centers to partner with, and plans volunteer collection rounds each week.

Part of the guide AI employees

By the xMap team · · 5 min read

An AI agent for nonprofits is a practical way for a small team to answer three recurring questions: which neighborhoods are far from the service you provide, which local businesses and community centers could become partners or donors, and in what order volunteers should visit their pickup stops each week. In xMap Flows each question is handled by an AI employee that runs on a schedule and sends a short list or a route to the coordinator who needs it.

This is for program managers, volunteer coordinators and operations staff at food banks, community health groups, youth charities, thrift networks and relief organizations. None of it needs a data team.

Where the service gaps are

A gap is a place where many people live and the nearest food bank, clinic or community center is a long way off. You can measure both halves.

Upload your own sites (and, if you like, those of other organizations doing the same work) as a table in My data. A Travel area block draws the area within a set walking time of each site, such as 15 minutes on foot, which is what matters to people without a car. Places outside every area are your candidates.

To weigh them, Demographics counts residents and age groups around a point: useful to see where children or people over 60 are most numerous. It has population figures only in some countries, including Canada, France, India, Egypt, Thailand and Australia, and none for the United States or the United Kingdom. Where it has no figures, Nearby places can stand in, by counting places that follow where people live, such as schools and grocery stores, as a rough sign.

The neighborhoods far from a food bank and older people far from a community center templates follow this pattern.

Partner sites and donors

Many nonprofits run on local partners: bakeries and supermarkets that give surplus food, community centers that host a weekly session, clinics and shelters to refer people to. Finding them is mostly a matter of a good list.

  • Nearby places lists the kinds of place you choose around each of your sites, with phone and website where known, and can keep only those currently open.
  • An xMap LLM block sorts them, for example into likely food donors, possible hosts and referral partners, and writes one line each.
  • Only new means a monthly run brings only places you have not seen, so the list grows instead of repeating.

The bakeries and supermarkets to ask for surplus food template is a direct start, and a referral directory of local support services keeps your caseworkers' list current.

Collection rounds for volunteers

Weekly pickups from partner stores are where volunteer hours go. The Route planner puts the stops in a good order from your depot, by car, bike or on foot, and can share them between several drivers. Each stop gets its place in the order, the distance and time from the stop before, and a directions link for the volunteer's phone. If you have more drivers than one route needs, Split by territory first gives each one a compact area.

A Weather forecast check the evening before can warn coordinators about heavy rain or heat on collection day. The routes for the weekly surplus food pickup template brings the stops and the route together.

A worked example (invented)

Picture a food charity in Montreal with four distribution points and twenty partner stores that donate surplus each Friday.

The gap flow draws a 15 minute walking area around each distribution point and checks the residents in the districts between them. One district in the east, outside every area, has a large number of residents, many of them children. The board uses that page to support a grant application for a fifth point.

The partner flow, run monthly, finds eleven bakeries and grocers near the existing points that the charity had not approached. The LLM marks six as likely donors. The coordinator calls those six.

Every Thursday at 18:00, the route flow splits the twenty stores between three volunteer drivers, orders each route from the depot, and emails the coordinator the three routes, each stop with its directions link, ready to forward. When the forecast shows heavy rain, the same email says so.

Pitfalls to watch

  • Straight-line gaps. A center 1 km away across a highway is not close for someone on foot. Use walking-time areas.
  • Using population where there is none. In countries without population figures, say so in your report rather than leaving a blank that reads as zero.
  • Routes longer than a volunteer's shift. Set the most stops per route to what one person can do, and add drivers rather than stops.
  • A partner list nobody calls. Assign each new partner to one person, or the monthly list piles up.

Setting it up in xMap Flows

  1. Service gaps: Schedule (quarterly), then My data (your sites), then Travel area (a 15 minute walk), then Demographics over each area, then xMap LLM to summarize who lives where, then Make a report emailed to the program manager.
  2. Partners: Schedule (monthly), then Area of interest around your sites, then Nearby places (bakeries, grocers, community centers), then xMap LLM to sort them, then Only new, then Email to the partnerships lead.
  3. Collection rounds: Schedule (Thursdays 18:00), then My data (partner stores), then Split by territory (your drivers), then Route planner (from the depot), then Weather forecast for the next day, then Email the routes to the volunteer coordinator.
  4. Run each once, check it, then Deploy. Each flow appears in the Team inbox, where staff can ask it questions about its last run.

For a wider view of how these workers fit a small team, read the guide to AI employees. To talk about your own programs, book a call.

Questions

Do we need a data analyst to run this?

No. Each flow is a few blocks on a canvas, and the templates named above can be started and adjusted by a coordinator.

Can it measure gaps in the United States?

It can draw walking areas and list services anywhere. Resident counts from Demographics are not available in the United States, so gaps there are judged by distance and by what is nearby.

Can volunteers see their route on a phone?

Yes. Each stop comes with a directions link for its part of the route, which opens on a phone.

Is our list of clients used?

Only if you upload it. The examples here use your sites, partner stores and public place and population data, not clients' details.

Templates that do this

Read next

More on ai employees and automation · Every article · Templates

Put it to work

An AI employee in xMap Flows does this on live data, on its own timetable. Start from a template or describe it in plain words.