How telecom field teams plan visits to towers and street cabinets
Turn a list of towers, cabinets and shelters into a day's rounds for each technician, with the weather and road closures checked before the vans leave the depot.
Part of the guide Workflow automation
Telecom field teams plan site visits by starting from the jobs due today, not from the full asset register: the towers, street cabinets and equipment shelters that need maintenance, a fault check or an upgrade. Those sites are shared between technicians by area, put in a driving order from the depot, and checked against two things that ruin a day in the field: bad weather at exposed sites and road closures on the way. The result is a short, ordered round per technician, sent before the vans leave.
This article is for network operations managers, field service coordinators and the contractors who run maintenance for operators. It explains how to turn a site list into rounds, what to check before dispatch, a worked example, common planning errors, and how an AI employee prepares the rounds every morning.
From the asset register to today's jobs
An operator or tower company may hold thousands of sites. Nobody plans a day from all of them. The day's list is usually built from three sources:
- Planned maintenance: sites whose inspection or service date falls this week.
- Faults and alarms: sites flagged by the network operations centre since the last plan.
- Projects: upgrades, new equipment, or surveys for new builds.
Keep each site's identifier, position, access notes and the job type in one table. The table is the source of truth; the round is just today's view of it. In xMap Flows that table lives in My data or in your own database, read by Database query.
Sharing sites between technicians
Once today's jobs are known, they need sharing out. Two patterns are common in telecom:
- Fixed patches. Each technician owns a part of the region. Each site already carries an owner, and each owner gets a round of their own sites.
- A shared pool from one depot. All technicians start from the same yard, and the jobs are split into compact groups, one per van.
For the shared pool, the Split by territory block divides the sites fairly by area, then the Route planner orders each group from the depot. The Route planner can also share stops between 2 and 10 people starting from the same place in one step. A round holds at most 50 stops, which is far more than a technician will visit in a day; climbing jobs may mean three or four sites, cabinet checks a dozen.
Checks before the vans leave
Telecom sites are often on hilltops, rooftops and roadsides, so two checks earn their place every morning.
Weather. High wind and lightning stop tower climbs; heavy rain makes some access tracks impassable. The Weather forecast block adds the day's wind, rain and temperature to each site, so a Filter can hold climbing jobs back when the forecast wind is too strong for your safety rule. You set the threshold: it is your safety policy, not a figure from this article.
Roads. A closure on the only road to a rural tower costs a whole morning. Traffic incidents lists closures and roadworks around each site, so the coordinator can swap the job for another before dispatch. For how busy the roads are right now, Traffic Flow gives current speeds and a jam factor around each place; it does not count vehicles.
A worked example
A made-up example: a contractor maintains sites for an operator around Bangkok. Today's table holds 26 jobs: 18 cabinet inspections in the city and 8 tower checks in the outer districts. Three technicians start from one depot.
- The flow reads the 26 jobs from the table at 5:45.
- The weather check finds strong gusts forecast at two hill sites; both tower checks are moved to tomorrow and the coordinator is told.
- A road closure sits on the access road to one cabinet; the job stays, but the note says to come from the east.
- The remaining 24 jobs are split into three compact groups and put in order from the depot.
- Each technician gets their round as a message: stop number, site id, job type, access notes, and a directions link.
The coordinator reviews the three rounds at 6:15, makes one swap by hand, and the vans leave at 7:00. The figures are invented; the point is that weather and roads were checked before anyone drove.
Planning errors that cost field hours
- Planning from the whole register. Rounds should come from today's jobs, or technicians drive past sites with nothing to do.
- No job time. A round with ten tower climbs looks short on a map and lasts three days in reality.
- Checking the weather at the depot only. Conditions on an exposed hill can differ from the yard in the valley; check each site.
- Ignoring access notes. Keys, gate codes and landlord contacts belong on each stop, not in someone's notebook.
- No record of the visit. A round that ends without a check-in leaves the next plan blind.
An AI employee that prepares the rounds
In xMap Flows one AI employee can prepare the rounds before the coordinator arrives:
- Schedule: weekdays at 5:45.
- My data: today's jobs table (or Database query on your own system).
- Weather forecast and Traffic incidents around each site.
- Filter: hold back climbing jobs above your wind rule.
- Split by territory, then Route planner from the depot.
- Email to the coordinator with all rounds, and a WhatsApp or Slack message to each technician.
What lands in the coordinator's inbox is one email with each technician's round, the jobs held back and why, and a map of the day. Technicians can check in at each stop from their phone, with a note and a photo, which feeds the next plan. The Tower field visits around weather and closures template has this shape ready to adapt.
Questions
Can the rounds start from each technician's home instead of a depot?
Yes. Give each site an owner and use one route for each rep; each round then starts where you set it for that person.
Does the route include time spent at each site?
No. Travel times are road times only. Add a job time per stop with a Calculated field to see the true length of the day.
Can it hold back tower climbs in high wind?
Yes. The weather forecast adds wind to each site and a Filter holds back the jobs above the limit your safety policy sets.
What if a road to a site is closed?
Traffic incidents lists closures and roadworks near each site, so the job can be moved or the access note changed before dispatch.