Trade area analysis: draw the area a store serves, then fill it in
A trade area analysis draws the area a store really serves by drive or walk time, then counts who lives in it, the rivals inside it and how busy the store's surroundings are.
Part of the guide AI employee for site selection
A trade area analysis answers one question for one store: where do its customers come from, and what does that area hold? You draw the area the store can reasonably serve (by drive time, walk time or distance along the roads, not a circle on a map), then count three things inside it: the people who live there, the competitors who also serve them, and how busy the store's own surroundings are. Done for two or three stores side by side, it explains why one outsells another and what a new store should expect.
This guide is for retail, restaurant, clinic and service businesses with physical sites, and for the property and franchise teams who place them. It explains primary and secondary trade areas, how to draw them in xMap Flows and what the drawing can and cannot do, what to count inside, a made-up comparison of two stores in Toronto, and the mistakes that make a trade area look better than it is.
Primary and secondary trade areas
Most stores draw the bulk of their customers from close by and a long tail from further out. Planners usually name two rings:
- Primary trade area: the core, where most regular customers live. For a neighbourhood bakery that may be a 10-minute walk; for a supermarket, a few minutes' drive.
- Secondary trade area: the next ring out, customers who come less often or pass by on their way somewhere.
Where the line falls is your judgement, ideally from your own loyalty or delivery data. If you have customer postcodes, plot them first; the trade area should fit them, not the other way round.
Drawing the area
The Travel area block draws, around each store, the area reachable within a travel time or a distance along the roads, by car, on foot or by bike. Two things to know:
- Range. For now it reaches up to 15 minutes or 10 km by road, which suits most city stores' primary and secondary areas, but not a regional destination people drive an hour to.
- Traffic. Travel times are for usual traffic, not the hour of the run. A drive area at 18:00 on a weekday may be smaller than the one drawn.
For two rings, use two Travel area blocks, one per range (say 6 and 12 minutes by car), each feeding its own counts. When the routing service cannot draw an area, the block falls back to an estimate, a circle at a typical speed, and says so in the step and every email.
What to count inside it
| Measure | Block | What it tells you |
|---|---|---|
| Residents, and by age | Demographics | How many people the area holds, where population data exists |
| Competitors and their ratings | Nearby places | Who else serves those residents, and how well |
| How busy the store's surroundings are | Mobility Footfall | People-hours of presence near the store, the busiest hour and day |
| Live road speed nearby | Traffic Flow | Whether the roads into the area are moving at the hours that matter |
Population figures exist only in some countries: Canada, France, India, Thailand, Egypt and Australia among them, not the UK or the US.
Two stores compared (made up)
This example is made up. A bakery chain has two Toronto stores of the same size; one sells a third more than the other, and the regional manager wants to know why before choosing a third site.
- Travel area draws a 10-minute walk around each store, and a second block a 6-minute drive for customers who come by car.
- Demographics counts residents inside each area: the walk area of the stronger store holds noticeably more people, many of them young families.
- Nearby places lists bakeries and cafes inside each area: the weaker store has more rivals in its walk area, two of them rated above 4.6.
- Mobility Footfall around each store, over the weeks of data there are so far: the stronger store's surroundings peak on Saturday mornings, the weaker store's at weekday lunchtimes, when office workers want a sandwich more than a loaf.
- The manager's conclusion: the weaker store is not badly run; it sits in a lunchtime trade area with tough rivals. The third site is chosen for residents and weekend footfall, and the weaker store adds a lunch offer.
Mistakes that flatter a trade area
- Using a circle. A 2 km circle crosses rivers, rail lines and motorways your customers will not. Draw by travel time.
- Counting every resident as a customer. Residents are potential, not demand. Compare stores on the same measure, not against a target.
- Ignoring overlap. If two of your stores' areas share streets, adding their residents counts those households twice.
- Treating footfall as visitors. People-hours rise when people linger. A busy park next door raises footfall without adding a single shopper.
- Drawing once. New rivals open inside areas. Recount every quarter at least.
Keeping it current with an AI employee
One flow can redraw and recount every store's trade area on a timetable, one of the jobs in the site selection guide:
- Schedule: the first Monday of each quarter.
- My data: your stores.
- Travel area: the walk or drive time you chose.
- Demographics and Nearby places inside each area.
- Mobility Footfall around each store.
- xMap LLM: a paragraph per store; Email and Show on a map.
Each quarter the inbox holds a short note per store (residents, rivals inside its area, its busiest hours) and a map of every area. The template rivals within 10 minutes' drive of each store covers the competitor part; builders' merchants within 15 minutes of my new site applies the idea to a trade customer, and where to open next uses the same measures to score new sites. For a step-by-step on the related idea of a catchment, see catchment area analysis.
Questions
What is the difference between a trade area and a catchment area?
They are often used for the same thing. Trade area tends to mean where a store's customers actually come from; catchment, the area it could draw on. The method of drawing and counting is the same.
Should I use drive time or walk time?
Use how your customers arrive. Walk time for a city-centre cafe or bakery, drive time for a supermarket or a store with a car park. Some stores need both.
How far can a trade area be drawn?
Up to 15 minutes or 10 km by road for now. That covers most city stores, not a destination people travel an hour to reach.
Can I see how many cars pass the store?
Not in most countries: Traffic Flow gives live road speeds and congestion, not car counts. Hourly car counts since 2021 exist only for roads in the United Arab Emirates, as a Regional data dataset.
Templates that do this
Read next
More on site selection and expansion · Every article · Templates