FlowsBook a callSign inCreate free accountSign up
Population and demographics

Using population to place a cash and carry warehouse

A cash and carry lives on the small shops and kitchens around it, and they live on residents. How to weigh people, trade customers and drive time when picking a site.

Part of the guide Location intelligence automation

By the xMap team · · 4 min read

Population matters to a cash and carry in a roundabout way: the warehouse sells to grocers, kiosks, cafes and restaurants, and those businesses exist because people live and work nearby. So a good site sits within a short drive of many small trade customers, and those customers sit among many residents. Measure both inside a realistic drive-time area, compare candidate sites on the same terms, and the population figure becomes a check on whether the trade customers will still be there in a few years.

This article is for wholesale and distribution businesses, FMCG companies opening trade outlets, and property advisers who serve them. It explains how residents and trade customers fit together, how to measure both around a candidate site, a worked comparison, mistakes that skew the numbers, and an AI employee that scores sites the same way every time.

Two kinds of demand around one warehouse

A supermarket counts households. A cash and carry counts businesses first. Its regulars are the owner of a corner grocery who drives in twice a week, the kitchen manager of a busy restaurant, the kiosk that restocks drinks every morning. Each of them chooses a supplier mostly on distance and stock.

Behind those customers are residents. A district with many people and few shops is a district where new shops will open; one with many shops and falling demand is one where they will close. That is why the two are measured together:

  • Trade customers in reach: grocers, convenience stores, kiosks, cafes, restaurants and hotels within the drive-time area.
  • Residents in reach: the number of people living in the same area, and how dense they are.
  • People per trade customer: residents divided by small food shops, a rough sign of whether shops are scarce or crowded.

Measuring around a candidate site

Start with the area a trade customer will actually drive. Business owners leave their shop to restock, so a short trip matters more than for a shopper. A 15-minute drive area around each candidate is a sensible first ring; the Travel area block draws it on the roads by car.

Inside that area, Nearby places counts the trade customers by kind: grocery and convenience stores, cafes, restaurants, hotels. Demographics adds up the residents from xMap's population grid, with men and women and nine age groups, and the people per square kilometre.

A Calculated field then works out the ratios the same way for every site, for example residents per grocery store and the share of food businesses that are independent, since chains often buy from their own warehouses.

A worked comparison

A made-up example: a distributor is choosing between two warehouse sites on opposite sides of Cairo. Both have the yard space and road access it needs.

Within a 15-minute driveSite A (east)Site B (west)
Residents1.1 million0.7 million
Grocery and convenience stores620540
Cafes and restaurants480610
Independent share of those food businesses88%79%
Residents per grocery store1,7701,300

Invented figures to show how the comparison reads; not measurements of Cairo.

Site B has more cafes and restaurants, but fewer of them are independent and residents per grocery store is lower, so its shops are already crowded. Site A has more residents for each shop and a higher independent share: more owners who buy for themselves and room for new shops to open. On these made-up numbers, Site A is the stronger long-term bet, even though Site B looks busier today.

Mistakes that skew the numbers

  • Using a circle instead of a drive area. A ring road, a river or a one-way grid changes who can reach the warehouse in 15 minutes.
  • Counting chains as customers. Supermarket chains usually supply their branches from their own depots. Count independents separately.
  • Reading residents alone. A dense residential district with few shops may be served by street markets that buy elsewhere. Look at the shops too.
  • Forgetting rivals. Count the other wholesalers and cash and carry outlets in the same area; a strong one next door changes everything.
  • Comparing sites in different countries on population. Coverage and methods differ; compare within one country.

An AI employee that scores candidate sites

In xMap Flows a site-scoring AI employee keeps every comparison consistent. One way to build it:

  1. My data: a table of candidate sites with their positions (and your current outlets, for comparison).
  2. Travel area: a 15-minute drive around each site.
  3. Demographics: residents and density in each area.
  4. Nearby places, set to pass on each site with counts: grocers, convenience stores, cafes, restaurants, and rival wholesalers.
  5. Calculated field: residents per grocery store, independent share.
  6. xMap LLM: a score from 0 to 100 with a reason, from your own brief.
  7. Make a report emailed to the expansion team.

What lands in the inbox is a ranked table of sites with the figures behind each score and a map. When a broker sends a new site, add it to the table and run again. The Neighbourhoods without a grocery store and Monthly outlet census of my city templates show the same building blocks in use.

Questions

Why does population matter if a cash and carry sells to businesses?

Because its customers, small shops and kitchens, depend on residents. Population shows whether those customers have room to grow or are already crowded.

What drive time should I use?

Start with 15 minutes by car for trade customers restocking, then test a shorter ring for the busiest districts.

Can I get population figures for any city?

No. Population data covers some countries only; where it is missing, compare sites on trade customers and rivals.

Should chain supermarkets count as potential customers?

Usually not. Most are supplied from their own depots, so count independents separately.

Templates that do this

Read next

More on population and demographics · Every article · Templates

Put it to work

An AI employee in xMap Flows does this on live data, on its own timetable. Start from a template or describe it in plain words.