FlowsBook a callSign inCreate free accountSign up
Roads and traffic

Isochrone maps explained: isochrones and isodistances

What an isochrone map shows, how isochrones and isodistances are drawn from real roads, how to read one, and when it beats a simple radius around a site.

Part of the guide Location intelligence automation

By the xMap team · · 5 min read

An isochrone is the area you can reach from a point within a given travel time, by a given way of travelling, following real roads and paths. Draw everywhere you could get to in 10 minutes by car from a shop and you get its 10-minute isochrone: an irregular shape that stretches along fast roads and stops short at rivers, railways and dead ends. Its sibling, the isodistance, is the same idea with a distance along the roads instead of a time. Both answer one question better than a circle can: who can actually get here?

This article explains the words, how the shapes are made, how to read one, and when it is worth using one instead of a simple radius. It ends with how xMap Flows draws them and hands them to other blocks. The glossary has the short version: isochrone vs radius.

The words, one at a time

  • Isochrone: from the Greek for equal time. Every point on its edge is the same travel time from the start.
  • Isodistance: every point on its edge is the same distance from the start, measured along the roads, not as the crow flies.
  • Isoline: the general word for either edge.
  • Travel mode: car, walking or cycling. Each follows different roads and paths at different speeds, so the same 15 minutes gives three different shapes.
  • Catchment: the area a business draws its customers from. An isochrone is one way of drawing it; the real catchment also depends on competitors and habits.

How the shape is made

A routing engine starts at the point and spreads outwards along the road network, adding up the time each stretch takes at a typical speed for that kind of road and that way of travelling. When the time runs out on a road, it stops there. Join up all the stopping points and you have the edge.

That process explains every odd feature you will see:

  • Long fingers along motorways and main roads, where a car covers ground quickly.
  • Bites taken out where a river has no bridge, a railway has no crossing or a park has no road through it.
  • Islands just off a motorway exit: reachable in time, while the land beside the motorway between exits is not.
  • Rounder shapes on foot. Walkers use paths and short cuts and move at the same pace everywhere, so walking isochrones look closer to circles, only much smaller.

How to read one

Three habits make an isochrone useful rather than decorative.

  1. Look at the edges, not the middle. The interesting parts are where the shape stops early. A neighbourhood just across a river from your site may be a long drive away; customers there will go elsewhere.
  2. Draw nested rings. Five, ten and fifteen minutes from the same point show how quickly reach grows. If the 15-minute shape is barely bigger than the 10-minute one, the site is boxed in.
  3. Overlay your other sites. Where the shapes of two of your stores overlap, they share customers. A new site whose shape mostly sits inside an existing one adds little new reach.

When an isochrone beats a radius, and when it does not

A radius is quick to explain and fine for comparing many sites in a dense, grid-like city where roads run everywhere. An isochrone earns its extra effort when geography is uneven: a coastline, a river, a hill town, a motorway that cuts a suburb in two, an edge-of-town site whose customers all arrive by car. Use an isodistance when the cost is per kilometre rather than per minute, such as a delivery charge or a service call-out fee.

For walking catchments in town centres the difference is smaller, but it still shows where a busy road without crossings keeps people on one side.

A worked example: one bakery, three ways of arriving

This example is made up. A bakery in Kyoto near the river wants to know who could reach it before work. It draws three 10-minute isochrones from its door: on foot, by bike and by car. The walking shape is small and stops at the river where the nearest bridge is a few minutes upstream. The cycling shape crosses that bridge and reaches two residential districts on the far bank. The car shape is the largest but follows the main roads out of town, towards areas that have their own bakeries.

The reading: the bakery's natural customers are cyclists from the far bank, and a sign at the bridge might do more than an advert in the car-heavy suburbs. A circle of the same size would have mixed all three groups together.

How to do it with an AI employee

In xMap Flows the Travel area block draws the shape: within a travel time in minutes or a distance in kilometres by road, by car, walking or cycling, around each incoming place or places you pick on the map. It currently goes up to 15 minutes and 10 km by road. It does not pass on items: it hands the blocks after it an area to search, as an Area of interest would, and each place they find carries the name of the area it fell in.

  1. My data: your stores, depots or candidate sites.
  2. Travel area: for example 10 minutes by car of each.
  3. Nearby places, set to Area of interest: competitors inside each shape. Or Demographics: the residents inside it, in the countries where population figures exist.
  4. Show on a map: the shapes and what was found in them.
  5. Email: the list, each place tagged with the area it came from.

What lands in the inbox is a map with each site's shape and a list such as rival stores within 10 minutes' drive of each of yours. When the routing service cannot draw an area, the block falls back to a circle at a typical straight-line speed and says so, in the step and in every email, so nobody mistakes an estimate for a real travel time. Templates that start here: Rivals within 10 minutes' drive of each store and Who my warehouse reaches in 15 minutes, for same-day delivery.

Questions

Is an isochrone the same as a catchment area?

Not quite. An isochrone is how far people could travel in a given time. A catchment is where customers actually come from, which also depends on competitors and habits. The isochrone is a good first draft of a catchment.

Why does my isochrone have holes or islands?

Because it follows the road network. Places next to a motorway but far from an exit, or across a river with no bridge, take longer to reach than places further away along a fast road.

Does it change with rush hour?

Not in xMap Flows: areas are drawn for usual traffic. Use Traffic Flow to see how the roads around a site are moving at a given moment.

How far can Travel area reach?

Up to 15 minutes and 10 km by road for now. For a wider look, use the Area of interest with a city or a drawn shape.

Templates that do this

Read next

More on roads and traffic · Every article · Templates

Put it to work

An AI employee in xMap Flows does this on live data, on its own timetable. Start from a template or describe it in plain words.