How tow truck firms watch road incidents within a drive of each yard
Alerts for tow truck dispatch incidents: closures and crashes reported within a short drive of each yard, sent to the dispatcher every few minutes, only once each.
Part of the guide Workflow automation
A towing company can watch for tow truck dispatch incidents by checking the roads inside a short drive of each yard every few minutes, keeping only closures and incidents it has not seen before, and sending each new one to the dispatcher with the nearest yard named. The alert does not replace a call from the police, a motor club or a customer; it tells the dispatcher where trouble is building so trucks and drivers are ready before the phone rings.
This article is for owners and dispatchers of recovery and roadside firms, fleet operators with their own breakdown trucks, and motor clubs that manage a network of tow partners. It explains what incident data shows and what it leaves out, how to draw the area each yard covers, a made-up example around Johannesburg, the rules to respect, and the AI employee that does the watching.
What the incident data shows
The Traffic incidents block reads road closures, roadworks and other incidents from online maps as they are right now. Each one comes back as an item with its kind (road closure, roadworks or incident), the street and district when it can be read from the position, the city or area it was found in, a position good to about 150 metres and an id that stays the same while the incident lasts.
Three limits matter for a towing business:
- Crashes appear as closures. For now accidents are reported as road closures, so a closure on a motorway at 02:00 may be a collision, a lorry that shed its load or planned overnight works. The street and the time usually tell you which.
- There is no severity. The data does not say how many vehicles are involved or whether anyone needs a tow. It says where the road is blocked.
- It is a snapshot. A check every five minutes sees what is on the map at that moment. A short incident cleared between two checks is missed.
Read in that light, the feed is a readiness signal, not a job sheet.
Drawing the area each yard covers
A circle around the yard is the quickest choice, but roads do not follow circles. A yard beside a motorway junction reaches far along the motorway and very little across a river with no bridge nearby. The Travel area block draws the area that can really be reached by car within a travel time or a road distance, following the roads, from each yard in your table. The blocks after it search inside those shapes as they would any area.
The ranges you can pick depend on your plan, and a short range works best for this job anyway: the incidents worth reacting to are the ones a truck can reach quickly. Firms with several yards get one shape per yard, so a city crossed by a ring road ends up covered by overlapping drive areas rather than one large circle.
A worked example around Johannesburg
The firm in this example is made up. It runs three yards: one north of the city near the main highway to Pretoria, one in the east and one to the south near an industrial area.
- Every five minutes between 05:00 and 23:00, and every fifteen overnight, the flow draws a short drive area around each of the three yards.
- Traffic incidents searches inside the three shapes for road closures and other incidents, leaving roadworks out because planned works rarely need a truck.
- Find nearest names the closest yard for each incident and how far it is.
- Only new drops incidents the flow has already reported, by their id, so a closure that lasts an hour is sent once, not twelve times.
- The dispatcher's phone gets a message: road closure on the highway northbound near an interchange, nearest yard north, about 4 km. A map link opens the spot.
On a quiet day the flow sends nothing. On a wet Friday evening it may send a burst of closures in one part of the city, and the dispatcher moves a spare truck towards that yard before the calls arrive.
Rules and good practice
In many cities, towing at a crash scene is allocated by the police or through a rotation list, and turning up uninvited is restricted or banned. Check the rules where you work. Used well, incident alerts help with things that are always allowed:
- Moving a truck or a driver on call closer to where incidents are clustering.
- Warning drivers already out on jobs about a blocked road on their way back.
- Telling a motor club or fleet customer that a delay is likely on a route.
- Planning the next shift from a week of incidents seen around each yard.
Mistakes to avoid
- Alerting on everything in the city. A message for every closure across a metropolis trains the dispatcher to ignore them. Limit the search to what the yards can reach.
- Leaving out Only new. Without it, the same incident is reported on every check while it lasts.
- Including all roadworks. Planned works fill the feed and rarely bring towing work. Leave them out, or send them in a separate morning summary.
- Checking too rarely. An hourly check is fine for planning, but for dispatch a short interval during busy hours is what makes the alert useful.
How to do it with an AI employee
In xMap Flows the watcher is a flow you build once and deploy. The blocks, in order:
- Schedule: every 5 minutes, with active hours if you want a slower rhythm overnight.
- My data: your yards, with their names and positions.
- Travel area: a short drive by car from each yard.
- Traffic incidents, Where set to Area of interest, with road closures and other incidents ticked.
- Find nearest: the closest yard to each incident.
- Only new: each incident once.
- A WhatsApp, Slack or Email block to the dispatcher, with a map saved on each run.
What lands with the dispatcher is one short message per new incident: its kind, its street, the nearest yard and the distance, with the spot on a map. If you prefer a trigger to a timer, the When something changes block can watch for a road closure near up to five places and run the flow only when it finds one. The incidents near my drivers' zones template is a close starting point, and towing partners along the highways helps a motor club build the partner list in the first place. More on alerts like these is in the field operations guide and on the automotive page.
Questions
Does the feed tell me when a car has crashed?
Not directly. Accidents are reported as road closures for now, without severity, so a closure may also be works or a breakdown. The street and time usually make it clear.
How often can the flow check?
A Schedule can run every 5, 15 or 30 minutes, with active hours, so busy hours can be checked often and nights less.
Will the same incident be sent again and again?
Not with Only new after the incidents block. Each incident keeps the same id while it lasts, so it is sent once.
Can I watch several yards at once?
Yes. Put your yards in a table; Travel area draws one drive area per yard and Find nearest names the closest yard for each incident.
Is it legal to use alerts like this?
Watching public road information is fine, but in many places crash-scene towing is allocated by police or a rotation list. Use the alerts for readiness and planning, and follow local rules.