FlowsBook a callSign inCreate free accountSign up
Roads and traffic

Live traffic data for business: what road speeds tell you, and what they cannot

Live traffic data for business gives road speeds and how jammed the streets around each site are now. The decisions it helps, an hour-by-hour picture, and its limits.

Part of the guide Location intelligence automation

By the xMap team · · 5 min read

Live traffic data for business tells you how the roads around each of your sites are moving at this moment: the current speed, the speed when the roads are clear, how jammed they are on a scale of 0 to 10, which road is the worst, and whether any are closed. It is a reading of speed, not of volume, so it answers "can we get through now?" and "how bad is it at 8 am here?", never "how many cars passed?". Run it at the hours you care about and keep the readings, and it becomes a picture of each site's roads through the day.

This article is for operations, dispatch, field service, events and site teams deciding whether road speeds are worth wiring into their work. It covers the figures you get, the decisions they help with, how to build an hour-by-hour picture from live readings, a made-up example from a caterer in Bangkok, the limits, and how to set it up as an AI employee.

The figures you get for each site

  • Current speed and free-flow speed in km/h, averaged over the roads around the site and weighted by the length of each stretch.
  • Jam factor from 0 (free) to 10 (standstill), and congestion as a percentage below free flow.
  • A level in words: free flowing, light, moderate, heavy or standstill.
  • The busiest road near the site, how many roads were measured and how many are closed.
  • When the reading was updated and how confident it is.

You choose how wide to look: the roads right next to the site (about 150 m), within 500 m, or within 1 km. Sites close together share one reading.

Decisions it helps with

TeamQuestionWhat to read
DispatchHold the vans ten minutes or send them now?Jam factor at the depot right before departure
Field serviceWhich visit first this morning?Speeds around each stop before the round
Events and venuesTell guests to allow extra time?Level and busiest road around the venue an hour before doors
Site selectionIs this site hard to reach at rush hour?Readings at the same hours over several weeks
Customer serviceWarn customers about late arrivals?Jam factor around the delivery zone at slot times

Common uses of live road speeds.

Building an hour-by-hour picture

A single live reading says what the roads are like at one moment. Most business questions are about patterns: is 08:00 always bad here, is Friday worse than Tuesday. Because the data has no built-in peak hours, you build the pattern yourself by reading at fixed times and keeping the results.

  1. Pick the hours that matter to the decision, for example 07:00, 08:00, 12:00 and 17:00 on weekdays.
  2. Read every site at those hours, with the same distance around each.
  3. Write each reading as a row in a sheet: site, date, hour, speed, free-flow speed, jam factor.
  4. After three or four weeks, average the jam factor by site and hour. The table that results is your own rush-hour map.

A made-up example: a caterer in Bangkok

Say a catering company in Bangkok delivers lunches to 12 office buildings and keeps missing the 11:30 slot at a few of them. It reads the roads within 500 m of each building at 10:30, 11:00 and 11:30 on weekdays for four weeks.

Building areaJam factor at 10:30At 11:00At 11:30Change
Sathorn4.16.37.8Leave by 10:30
Silom3.64.04.4No change
Asok5.27.18.0Leave by 10:15

Made-up four-week averages for illustration only.

Silom stays manageable, so its schedule stays. Sathorn and Asok climb steeply after 10:30, so the caterer moves those vans earlier and adds a live check at 10:20 that warns the driver when the jam factor around the building is already above 6. Late deliveries fall without adding a van. None of this needed car counts: speed and jam factor were the right measures for the question.

What it cannot do

  • Count cars. Live speed data measures how fast traffic moves, not how much of it there is. For counted cars hour by hour, xMap has road traffic history for the United Arab Emirates only, from January 2021, as a regional dataset.
  • Show the past by itself. Each reading is taken when the flow runs. History is what you keep.
  • Split by direction or lane. The figures describe the roads around a site together, with the single worst road named.
  • Replace closure alerts. For closures and roadworks across a whole area, use Traffic incidents alongside it.

Setting it up as an AI employee

In xMap Flows the readings come from the Traffic Flow block, and an AI employee takes them at your hours and sends or stores them. The location intelligence automation page puts it beside the other live data.

  1. Add a Schedule with several times a day (for example 07:00, 08:00 and 17:00) on weekdays.
  2. Bring in your sites with My data, or find venues with Nearby places.
  3. Add Traffic Flow with Roads set to within 500 m.
  4. Add a Filter on the jam factor (for example 6 or more) for alerts, or skip it to keep every reading.
  5. Send alerts by Email, Slack or WhatsApp, or write every reading to a sheet in Google Sheets to build the hour-by-hour picture.

What lands is one line per site: the level, the jam factor, the current and free-flow speed, and the busiest road, or nothing at all when every site is moving. Templates to start from: Road speeds around the airport, every hour and Road speeds around the stadiums, every hour. To add closures, put Traffic incidents in the same flow; for counted cars on UAE roads, use Regional data sources.

Questions

Does live traffic data count vehicles?

No. It gives speeds, the jam factor and congestion. Counted cars by the hour are available only for roads in the United Arab Emirates, through a regional dataset.

How current is the reading?

It is taken when the flow runs, and each site's reading carries the time it was last updated.

How do I find a site's rush hour?

Read it at fixed times on weekdays for a few weeks, keep each reading in a sheet, and average the jam factor by hour.

What does a jam factor of 7 mean?

Heavy traffic: the roads are moving far below their free-flow speed. 0 is free flowing and 10 is standstill.

Templates that do this

Read next

More on roads and traffic · Every article · Templates

Put it to work

An AI employee in xMap Flows does this on live data, on its own timetable. Start from a template or describe it in plain words.