FlowsBook a callSign inCreate free accountSign up
Workflows by industry

How theme parks plan around their access roads on peak days

Theme park traffic planning for the busiest days: watching live speeds and closures on the roads guests use to arrive, and telling the right team in time.

Part of the guide Workflow automation

By the xMap team · · 5 min read

Good theme park traffic planning on peak days comes down to knowing, every few minutes from early morning, how fast the roads into the park are moving and whether any of them is closed, then acting on it before the queue reaches the car park. Operations teams do this by measuring live speeds and incidents at a handful of fixed points on the approach roads, comparing them with the free-flowing speed, and sending a short alert to the people who open extra gates, staff the car parks and update guest messages.

This article is for operations, guest services and car park managers at theme parks, water parks, zoos and other large attractions. It covers which roads to watch, how to read what live traffic data tells you (and what it does not), a made-up example, the usual mistakes, and the AI employee that runs the checks on the days that matter.

Choosing the roads to watch

Most parks have a short list of ways in: one or two motorway exits, a main access road, a back road locals use, and perhaps a coach drop-off. Pick a point on each, close to where a slowdown would first affect your gates. Five to ten points are usually enough; more makes the alerts harder to act on.

Store them in a table with a name staff will recognise ("North exit ramp", "Coach road") and a position. That table is what every check runs on, and it is easy to change when roadworks move the main route for a season.

What live traffic data can and cannot tell you

  • Speed against free flow. The Traffic Flow block measures the roads around each point when the flow runs: the current speed, the speed when roads are clear, the congestion as a percentage, a jam factor from 0 to 10, a level from free flowing to standstill, and the busiest road nearby.
  • Closures and incidents. The Traffic incidents block finds road closures, roadworks and other incidents reported on online maps near each point, with the street and how far away the closest one is.
  • What it does not do. Neither block counts cars, and live data has no peak hours or direction split. Run the checks at the times you care about, and keep your own gate and car park counts as the measure of arrivals.

A made-up peak day

Imagine a park outside Osaka on the first day of a school holiday, opening at 09:00. Its flow checks seven points every 15 minutes from 06:30 to 11:00 and again from 16:00 to 20:00 for departures.

At 07:45, in this invented case, the motorway exit ramp shows a jam factor of 7 and speeds at about a third of free flow, while the back road is clear. The alert to the car park lead and guest services reads, roughly: north exit ramp heavy, 18 km/h against 60 free flowing; back road free flowing; no closures within 2 km. The car park team opens the overflow lot by the back road, and guest services posts a message suggesting the alternative route. At 08:30 the ramp drops back to moderate and the next check says so, so the overflow staff can be moved again.

Building the peak-day AI employee

In xMap Flows this is a short flow, switched on for peak days and paused otherwise:

  1. Schedule: every 15 minutes, active between 06:30 and 11:00 and between 16:00 and 20:00, in the park's time zone.
  2. My data: the table of approach points.
  3. Traffic Flow: adjacent roads around each point.
  4. Traffic incidents: around each incoming place, within 2 km, so each point also carries the number of incidents nearby.
  5. What changed:set to watch another field, the traffic level, so only points whose level changed since the last check go on, in either direction, and a check where nothing moved sends nothing.
  6. Filter (optional): on a road you only care about when it is bad, keep the points with a jam factor of 6 or more.
  7. A Slack message to the operations channel, or an email to the duty manager, with each point, its level, its speed and the nearest incident.

Templates that already do much of this for other kinds of venue are road speeds around the stadiums, every hour, road speeds around the airport and road incidents around the race route. Swap in your own points and timetable.

Mistakes to avoid

  • Watching only the motorway. The last kilometre often jams first, at the turn into the car park. Put a point there.
  • Forgetting the evening. Departures after fireworks or a late show can block the same roads in the other direction. Schedule an evening window too.
  • Running it every day all year. On quiet weekdays the alerts add nothing. Deploy it for the calendar of peak days and pause it in between.
  • No named person. An alert that reaches a channel nobody owns at 07:45 is wasted. Name who acts on it, and test the flow on a normal weekend first.

The same thinking applies to festivals, stadiums and exhibitions, covered on the events and venues and hotels and tourism pages. For how teams hand this kind of watching to an AI employee generally, see the guide on the AI employee for field operations, or book a call to walk through your own roads.

Questions

Can it tell me how many cars are heading to the park?

No. Traffic Flow gives live speeds and a jam factor, not vehicle counts. Hour-by-hour car counts exist only for roads in the United Arab Emirates, through Regional data.

How often should the checks run?

Every 15 minutes is a good start on peak mornings. Every 5 minutes is possible but rarely changes what staff do, and makes more messages to read.

Can guests see the alerts?

The flow sends to your staff. Guest services can then post an update on your own channels; the alert gives them the facts to do it quickly.

Does it work for a park in a small town?

Yes, as long as the approach roads are measured. A point with no measured roads around it says so in its result rather than showing a made-up speed.

Templates that do this

Read next

More on workflows by industry · Every article · Templates

Put it to work

An AI employee in xMap Flows does this on live data, on its own timetable. Start from a template or describe it in plain words.