Furniture delivery scheduling around routes, time windows and slow roads
Two-person crews, big vans and four-hour windows: how to order a furniture delivery day, warn customers early and keep an eye on the roads that slow it down.
Part of the guide Location intelligence automation
Furniture delivery scheduling is harder than parcel planning because every stop is long, the van is large, and the customer has taken a morning off to wait. A good day is built in three layers: the stops put in a sensible order from the depot, a promised window for each customer that leaves room for carrying and assembly, and a morning check of the roads the van will use, so a closure or a jammed bridge is known before the crew sets off rather than at the second stop.
This article is for furniture and appliance retailers that run their own vans, and for the small two-person delivery firms they contract. It covers what makes bulky stops different, how to set windows customers can trust, which road readings help, a worked example in Lisbon, and an AI employee that prepares tomorrow's run and today's road note.
Why bulky stops break normal route plans
A parcel stop takes a couple of minutes. A sofa up three floors, a wardrobe assembled in a bedroom or an old mattress taken away can take forty minutes or more. That changes how you plan.
- Fewer stops, longer gaps. Eight to twelve stops is a full day for a two-person crew. Travel time is a smaller share of the day, but one bad leg still pushes every later window.
- Parking and access count. A narrow old-town street, a loading bay or a lift booking can matter more than the drive itself.
- The order of loading follows the route. The last stop goes in first. Changing the order on the morning means reloading the van.
- Customers wait in. A missed window is a lost day for them, and often a second trip for you.
Ordering the day
The Route planner block takes the day's addresses and puts them in the best visiting order from a start you pick, such as the warehouse. It can make one route, one route for each crew named in a field, or share the stops between 2 and 10 vans so each gets a compact day. Each stop comes back with its place in the route, the kilometres and minutes from the stop before, the minutes of travel from the start, and the route's totals.
Those travel minutes are without time spent at stops, so add your own handling time per job type. A simple rule works well: say 20 minutes for a small item, 40 for anything that needs assembly, 60 for a bedroom set. A Calculated field can add that to each stop and work out a promised window.
The roads that matter on the morning
Route orders are planned from typical travel times. On the day, two things change the picture: closures and slow roads. Traffic incidents lists road closures, roadworks and other incidents in a city, or around each stop within a distance you set. Traffic Flow gives the live speed against free-flow speed and a jam factor from 0 to 10 for the roads around each point, measured when the flow runs. It does not count vehicles and it is a snapshot, so check it near departure time, not the evening before.
For furniture vans, add a few fixed points to the morning check: the depot gate, the bridge or tunnel most routes cross, and the ring road junction the vans join. Those are where a big vehicle loses the most time, because it cannot take the side streets a car would use.
A worked example in Lisbon
Say a furniture shop in Lisbon has 19 deliveries for Thursday and two crews. This is an invented example to show the steps.
- At 4 pm on Wednesday the day's orders are in a sheet with addresses and job types.
- Route planner shares the 19 stops between two vans from the warehouse, one compact area each, and orders them.
- Handling minutes are added per job and each customer gets a window, sent by message that evening.
- At 6:45 am on Thursday a road check runs on the depot gate, the bridge both vans cross and every stop. The bridge reads Heavy with a jam factor of 7, and a roadworks site sits 300 m from stop 4 of van one.
- The crew lead sees the note before loading, moves the bridge crossing later by swapping two stops, and phones customer 4 about access.
Nothing in that example needed a planner at a desk at dawn. The order, the windows and the warning came from the flow; the people made the call.
Mistakes to avoid
- Reordering the route on the morning without reloading the van to match.
- Promising equal two-hour windows all day.
- Checking traffic the night before. Speeds are live and only useful near the time you drive.
- Ignoring a closure because it is not on the route line. A closure near a stop often means no parking for a large van.
An AI employee for the delivery desk
Two small flows cover the job. The first runs every afternoon: New rows or My data brings in tomorrow's orders, Route planner orders them per van, a calculated field adds handling time and windows, and an email or sheet row goes to the crews. The second runs at 6:30 every weekday: the depot and stops come in, Traffic incidents adds the nearest closure to each, Traffic Flow measures the key points, and a short note goes to the crew chat. The Road speeds outside my depots, every hour and Road closures in my city templates are close starting points. More delivery patterns sit in the guide to AI employees for field operations.
Questions
How many furniture deliveries can one crew do in a day?
It depends on the jobs and the city, but long handling times mean far fewer stops than parcel rounds. Plan with your own handling minutes per job type and let the route totals show what fits.
Does the route planner use live traffic?
It orders stops from typical travel times. Check live speeds and closures separately on the morning, close to departure.
Can each van get its own route?
Yes. Route planner can make one route for each crew named in a field, or share the stops between 2 and 10 vans.
Can customers get their window automatically?
Yes. Once each stop has a window, an email or app message per item can send it to the customer.