Population within radius, Australia: residents around a point in Sydney and Melbourne
Count the people living within 1, 3 or 5 km of any address in Sydney or Melbourne, with ages, and see why the same radius means very different numbers across a city.
Part of the guide Location intelligence automation
To work out population within radius Australia-wide, drop a point on the address, choose a distance, and add up the residents of every small hexagon inside the circle. Australia is covered by xMap's population grid, so for any spot in Sydney or Melbourne you get the total, men and women, nine age groups and people per km² within anything from 500 m to 8 km. The answer comes back in seconds and is the same method for every site, which makes candidate locations comparable.
This is for franchise and retail expansion teams, gym and childcare operators, medical practices, property developers and councils. It explains how the radius count works, why Australian cities make radius numbers swing so much, a made-up comparison of two sites, the traps, and an AI employee that runs the count for every new site.
How a radius count works
Demographics takes a point and a distance, or a list of your own places, and returns the residents living inside the circle, built from hexagons of about 0.1 km². Each result carries the population, men and women, ages from 0 to 9 up to 80 and over, children, working-age adults and seniors with their shares, the area of the circle and the people per km². Give it up to 200 places in one run and each gets its own figures.
Why the same radius gives very different numbers
Australian cities are low and wide. Apartment towers cluster in the centre and around some train stations; most suburbs are detached houses on large blocks; water and bushland cut through both cities.
- Sydney: a 2 km circle around a dense hub such as the CBD fringe, Parramatta or Chatswood holds far more people than the same circle in an outer suburb of houses, and a circle on the harbour or near a national park loses a large slice to water and bush.
- Melbourne: inner suburbs like Fitzroy, Richmond and South Yarra are dense for Australia, while growth suburbs on the western and south-eastern edges spread the same number of people over a much bigger area. Port Phillip Bay takes a bite out of any circle on the bayside.
So never set one radius for the whole country and read the totals as like for like. Decide the distance by how customers reach you: walking distance in the inner city, a short drive in the suburbs.
A made-up example: a childcare operator
Invented, to show the method. A childcare operator is choosing between two leases in Melbourne: one in an inner suburb, one in a growth suburb on the city edge. It counts children aged 0 to 9 within 2 km of each, then within 5 km.
| Made-up site | Residents within 2 km | Children 0 to 9 within 2 km | Children 0 to 9 within 5 km |
|---|---|---|---|
| Inner suburb | 38,000 | 2,900 | 14,500 |
| Growth suburb | 16,000 | 2,700 | 11,800 |
Invented figures to explain the reading; not data about Melbourne.
The inner suburb has more than twice the people, yet nearly the same number of young children within 2 km, because the growth suburb is full of young families. With parents in the growth suburb driving to childcare, the 5 km count matters more there. The operator then runs Nearby places to count childcare centres within each circle before deciding.
For context: how busy these city centres are
Population tells you who lives near a site; the places around it tell you about competition. As an example, xMap's places database lists 2,573 cafes and 692 gyms within 10 km of the centre of Sydney (November 2026). A radius count of residents read beside counts like these is what turns a pin on the map into a decision.
Traps to avoid
- One radius everywhere. Inner Sydney and outer Melbourne need different distances.
- Water in the circle. Harbour, bay and river sites lose part of their circle; compare people per km² as well as totals.
- Residents as shoppers. A CBD site may have few residents and many workers. The count is where people live.
- Too big a circle. One search covers up to 8 km. For a wider region, draw it as an area and ask for totals.
- Copying the method to the US or UK. The grid has no figures there, so this exact analysis works in Australia but not in those two countries.
An AI employee for every new site
- A Form page or My data brings in the candidate addresses.
- Demographics: residents within 2 km of each, with ages.
- Nearby places: competitors within the same 2 km, counted.
- xMap LLM: a short note on each site, using only those figures.
- Sort and limit, and an email with every site, its people, its competitors and the note.
Similar ready flows: Who lives around new places and Competitor density around each site. Expansion teams will find the full method in the AI employee for site selection and location intelligence automation.
Questions
Does xMap have population data for Australia?
Yes. Australia is covered by xMap's population grid, including Sydney and Melbourne, with residents and nine age groups per hexagon of about 0.1 km².
What radius can I use?
From 500 m to 8 km around each point. For a larger area, draw it in the Area of interest and ask for totals.
Can I count only children or only seniors?
Each result includes nine age groups plus children, working-age adults and seniors, so you can sort or filter by the group you serve.
Is a drive time better than a radius?
Often in the suburbs, where people drive and roads bend. A Travel area gives a drive or walk catchment and Demographics counts residents inside it.
Templates that do this
Read next
More on population and demographics · Every article · Templates