FlowsBook a callSign inCreate free accountSign up
Population and demographics

Population and parking demand around a shop: how to judge whether customers can park

A shop that needs drivers needs somewhere for them to stop. How to weigh the people living nearby against the car parks around a site, and what the data cannot tell you.

Part of the guide Location intelligence automation

By the xMap team · · 5 min read

To judge parking demand around a shop, put two counts side by side: how many people live within a short drive, which tells you how many might come by car, and how many car parks and garages are listed within a few minutes' walk of the door, which tells you where they could leave the car. Many residents and few car parks means parking will be the bottleneck; few residents and plenty of parking means the shop must draw from further away. Neither count says how full a car park is at four on a Saturday, so finish with a visit at the hours that matter.

This is for retailers whose customers carry things home: furniture, hardware, garden centres, bulk grocery, pet supplies, appliances, and for clinics and gyms in places where most people drive. It covers what each count means, how to combine them, a worked example and an AI employee that does the counting for a list of sites.

Why parking deserves its own check

Shoppers forgive a lot, but not circling the block. A site can have the right people around it and still underperform because the only car park nearby is full of commuters by nine in the morning. The reverse happens too: a site on the edge of town with a large car park and few homes nearby can do well if it is the only one of its kind within a long drive.

Parking is rarely in a site brochure in useful form. The landlord says there is parking; the question is how much, how close and shared with whom.

Count one: people within a short drive

The Demographics block counts residents, men and women and nine age groups from xMap's population grid, inside any area you give it. Draw the area with Travel area as a drive time, say 10 minutes by car, so it follows the roads instead of a circle that crosses a river or a motorway. Travel area hands the blocks after it an area rather than your sites, so it suits looking at one site at a time; to compare a list of sites in one flow, set Demographics to each incoming place with a distance (up to 8 km), and every site keeps its own row with the residents around it.

Population is where people sleep, not where they are during the day. For a shop that trades at lunchtime in a business district, a footfall reading tells you more about the daytime crowd than residents do.

Count two: car parks within a walk of the door

Nearby places can count the parking types in xMap's places database around a point: parking lots, parking garages and parking grounds. Set it to each incoming place, with counts, within 300 or 500 m, a walk people will make with a heavy bag. Each site comes back with how many parking places are listed and the nearest one with its distance.

Read the count with care:

  • A listed car park has no size. A ten-space lot and a six-floor garage are one place each. Look at the nearest few on a map before trusting the number.
  • Street parking is not listed. In many cities most parking is on the street, so a low count can still mean easy parking.
  • Shared car parks fill early. A car park next to a station or an office block may be full on weekdays and empty at weekends.
  • No occupancy. The data says where car parks are, not how full they are or what they charge.

Putting the two together

The simplest measure is residents per listed car park within the walk you chose. It is crude, but it is the same crude measure for every site, which makes it useful for ranking a shortlist. A Calculated field works it out in one line. Add two more readings before deciding:

  • How busy the area already is. Mobility Footfall gives footfall per day as people-hours of presence, and the busiest hour and day, in the cities it covers. A site whose busiest hour matches your own busiest hour will compete for the same parking. The figures arrive about ten days after the day they describe.
  • How the roads move. Traffic Flow gives the current speed and a jam factor on the roads around each site. It does not count cars, but a road that is slow at the hours you trade makes the last few hundred metres to the car park hard.

A worked example: three sites for a garden centre near Lyon

This example is made up, with invented numbers to show the arithmetic. A garden centre chain weighs three sites around Lyon. For each, it draws a 10-minute drive area, counts the residents, and counts the car parks listed within 400 m.

Site (made up)Residents in 10 min by carCar parks within 400 mResidents per car park
Site A, inner suburb180,000360,000
Site B, ring road95,0009about 10,600
Site C, small town40,0006about 6,700

Made-up figures, to show how the measure is worked out and read.

Site A has the most people and the least parking: unless the unit comes with its own car park, customers will struggle. Site C has easy parking but a small pool of people. Site B sits between and, on these numbers, deserves the first visit. The visit then checks what the counts cannot: whether the nine listed car parks are big, free and open when the shop is.

How to do it with an AI employee

For a list of candidate sites, the blocks in order:

  1. My data: your candidate sites, or existing stores you want to compare.
  2. Demographics: each incoming place, residents within 3 km.
  3. Nearby places: parking lots and parking garages, each incoming place with counts, within 400 m.
  4. Calculated field: residents per car park.
  5. Sort and limit, then Email: the sites in order, with each count.

What lands in the inbox is one table: each site with its residents, its listed car parks, the nearest car park and its distance, and the ratio, best first, plus the step notes saying where any figure is missing. The Busy places that need more parking template turns the question around for car park operators, and Parking and transit around the venue does the same counting for a guest guide.

Questions

Can xMap tell me how full a car park is?

No. It knows where car parks are listed, not how many spaces they have, how full they are or what they charge. Use the count to shortlist and a visit to decide.

Why use a drive time for residents but a walk for parking?

Customers drive to the area, then walk from wherever they parked. The drive time sets who might come; the walk sets where they can stop.

What if my country has no population figures?

Use counts of homes, offices and other businesses around the site from Nearby places as a stand-in, and footfall where it is measured.

Does Traffic Flow count the cars on the road?

No. It gives live speed, free-flow speed and a jam factor. Car counts by hour exist only for main roads in the United Arab Emirates, as a regional dataset.

Templates that do this

Read next

More on population and demographics · Every article · Templates

Put it to work

An AI employee in xMap Flows does this on live data, on its own timetable. Start from a template or describe it in plain words.