FlowsBook a callSign inCreate free accountSign up
Roads and traffic

Traffic around a new stadium or arena: what to measure before the first event

A new venue changes the roads around it on event nights. How to record the roads before it opens, read live speeds on the night, and spot the closures that make it worse.

Part of the guide Location intelligence automation

By the xMap team · · 5 min read

To understand traffic around a new stadium or arena, record the roads before it opens and then measure them the same way on event nights. Live road speed, free-flow speed and the jam factor on the roads around the venue, taken every 15 minutes, show how far an event slows each road and for how long. Road closures and roadworks explain the worst nights. Car counts are a different measure and, in xMap Flows, are available only for roads in the United Arab Emirates.

This is for venue operators, event organisers, businesses near a new venue (restaurants, hotels, car parks, delivery firms) and city transport teams. It covers what a baseline is and why it matters, which measures to take, a made-up example, and an AI employee that records the roads for you.

Why measure before the doors open

Once a venue is running, every busy evening has an obvious cause. Without a record from before, nobody can say how much of the congestion is the venue and how much was always there. A few weeks of measurements at the same hours, before the first event, give you that record. Then the first concerts and matches can be compared with it road by road.

A baseline answers questions that come up quickly after opening: does the venue jam the main road for an hour or for three? Does the side street residents complain about actually slow down? Did a new bus lane or parking rule help?

What the measures mean

Traffic Flow measures the roads around each place at the moment the flow runs. For each place it gives:

  • Current speed and free-flow speed, in km/h. Free flow is how fast the road moves when it is empty; the gap between them is the delay.
  • Jam factor, from 0 (free) to 10 (standstill), averaged over the road stretches measured.
  • Congestion, as a percentage below free-flow speed, and a level in words from Free flowing to Standstill.
  • Roads measured, roads closed and the busiest road, so you know which stretch is driving the figure.

You choose how wide to look: the roads adjacent to the place (about 150 m), within 500 m, or within 1 km. For a stadium, measure several points rather than one wide circle: the main entrance, the car park exit, the nearest junction on the main road, and a residential street on the far side.

Traffic incidents adds the other half of the story: closures, roadworks and accidents near the venue, each with its street and type. An event night with a closed slip road will look very different from one without, and you want to know which nights to set aside when comparing.

Car counts where they exist

For venues in the United Arab Emirates there is a second source. The Regional data block's road traffic history counts cars and their speed hour by hour on the main roads within 500 m of a place, going back to January 2021. Around an existing arena in Dubai or Abu Dhabi you can compare event evenings with ordinary evenings over years, or check how a road near a planned venue behaves today. Outside the UAE no car counts are available, so speed and jam factor are the measures.

A made-up example in Lisbon

Invented figures to show the method. A city transport team in Lisbon expects a new 12,000-seat arena to open in spring. It measures four points every 15 minutes from 5 pm to midnight on weekdays for six weeks before opening, then on every event night after.

Made-up figures, 9.30 to 10.30 pmBefore openingEvent nights
Main road junction, average speed41 km/h17 km/h
Main road junction, jam factor2.16.8
Car park exit street, jam factor1.48.2
Residential street, jam factor0.91.6

Illustrative figures only.

On these figures the main junction loses well over half its speed for the hour after an event ends, and the car park exit street comes close to standstill. The residential street that neighbours worried about barely moves. The team staggers the car park exits and adds a left-turn phase at the junction, then compares the next month's event nights with the same table.

Who else watches the roads

  • Restaurants and bars nearby learn when guests can actually reach them before a show, and when after.
  • Hotels can tell guests when to leave for the venue and when the roads clear.
  • Delivery and courier firms can move drops away from the hour before doors open.
  • Event organisers can put road advice in the ticket email, written from measured nights, not guesses.

An AI employee that records the roads

  1. Put the measuring points in a table on the My data page: entrances, exits, junctions and a quiet street.
  2. Start with a Schedule every 15 minutes, with active hours set to the evenings and days you care about.
  3. Add Traffic Flow with Within 500 m, and Traffic incidents around the same points.
  4. Save each reading with a sheet or Save to my database, so the readings build into a record you can chart.
  5. Add a Filter on the jam factor and an Email to the operations team when a point goes above your limit on an event night.

Before opening, the flow quietly builds the baseline. After opening, the operations team gets an alert only when a point jams beyond the agreed limit, and a full record of every evening is there for the review after each event.

Questions

Can I count the cars going to an event?

Not with live traffic data, which measures speed and congestion. Hour-by-hour car counts since 2021 exist only for roads in the United Arab Emirates, through the Regional data block.

How often should I measure on an event night?

Every 15 minutes from a couple of hours before doors open to an hour after the end shows the build-up, the peak and how long it takes to clear.

Why measure before the venue opens?

Without a baseline there is nothing to compare event nights with, so nobody can say how much congestion the venue adds or whether a change helped.

What does a jam factor of 6 mean?

The jam factor runs from 0 for free-flowing traffic to 10 for standstill. Around 6 means heavy congestion, with traffic moving well below the road's free-flow speed.

Templates that do this

Read next

More on roads and traffic · Every article · Templates

Put it to work

An AI employee in xMap Flows does this on live data, on its own timetable. Start from a template or describe it in plain words.