How to compare traffic at two locations, hour for hour
Live speeds and the jam factor side by side for two addresses, measured at the same hours over several days, plus a one-click comparison of the sites themselves.
Part of the guide Location intelligence automation
To compare traffic at two locations fairly, measure both at the same moments: the same hours, the same days, the same distance of road around each, repeated over a week or two. Look at the current speed against the free-flow speed and at the jam factor, which runs from 0 for clear roads to 10 for a standstill. One reading taken on a whim tells you how a single afternoon looked; a set of readings taken side by side tells you which spot really sits in slow traffic, and when.
This is for anyone choosing between two addresses where the roads matter: a tyre fitter or car wash deciding between plots, a clinic weighing two units with patient parking, a logistics team picking between two yards, a franchisee told that one corner is "much busier". It covers what to measure, how to set up the readings, a made-up example, what live speeds cannot tell you, and the quicker check when you only need a first look.
What to measure at each address
The Traffic Flow block reads the roads around each place at the moment the flow runs and gives every place the same set of fields:
- Current speed and free-flow speed in km/h, averaged over the roads around the place and weighted by the length of each stretch.
- Congestion as a percentage: how much slower than free flow the roads are right now.
- Jam factor, 0 to 10, and the same thing in words: free flowing, light, moderate, heavy or standstill.
- Roads measured, roads closed and the busiest road by jam factor, so you know whether one blocked street is skewing the average.
Pick how far to look: the roads right next to the place (about 150 metres), or every road within 500 metres or 1 km. For a site customers drive into, the adjacent roads matter most. For a yard where trucks need to reach a main road, the wider ring says more.
Setting up a fair side-by-side
Fairness comes from doing everything to both places at once. Put both addresses in the same flow so they are measured in the same run, seconds apart.
- List the two addresses in a small table in My data, or pick them in the flow.
- Add a Schedule that runs at the hours that matter to the business: say 8:00, 12:30 and 17:30 on weekdays, and late morning on Saturday for a shop people drive to at the weekend.
- Add Traffic Flow with the same road distance for both.
- Send each run's two rows to a sheet with the time, so the rows pile up into a table by hour and day.
- After ten working days or so, average each address's speed and jam factor by time slot and read the gaps.
A made-up example: two plots in Lisbon
The figures in this example are invented. A tyre and service chain has two plots on offer in Lisbon: one on a busy avenue near a motorway exit, one on a side road in a residential district. The avenue plot is described by the agent as the obvious choice because "everyone drives past".
Two weeks of readings tell a fuller story. At 8:00 the avenue's jam factor is often heavy and its speed less than half of free flow; the side road is light. At midday both are free flowing. At 17:30 the avenue is heavy again, with one closed stretch on two of the days. The side road never goes above moderate.
For a business whose customers must turn in, park and drop a car off before work, the avenue's morning queue is a problem, not an advantage: drivers stuck in it are not going to cross three lanes to reach the forecourt. The chain shortlists the side-road plot, then checks the avenue plot's other entrance before deciding. The readings did not choose the site; they turned "everyone drives past" into a question that could be answered.
The one-click check first
Sometimes you want a quick first look before setting up two weeks of readings. Compare sites on the map measures two or three spots the same way in one go: road speed sits in its rows beside the people who live around each spot, rival businesses, the nearest station, car parks and more, with the best of each row marked and a short verdict. The help article on comparing sites side by side shows how to drop the pins.
Its road speed is a single moment, the time you pressed the button, so treat it as the opening line of the comparison. The scheduled flow is what tells you how each place behaves through the week.
What live speeds cannot tell you
- How many cars pass. A slow road can carry few cars and a fast one many. Speed is about delay, not volume.
- Which way they are going. The average covers both directions, so a site on the inbound side of a morning queue looks the same as one on the outbound side.
- Hours you did not measure. If the flow never runs at 19:00, you know nothing about 19:00.
In the United Arab Emirates, the Road traffic history dataset in Regional data does count cars hour by hour on the main roads near a place, back to January 2021, so a comparison there can add volume to speed. Elsewhere, speed and jam factor are the measures.
Traffic is one strand of a wider location picture; the location intelligence automation guide shows how it sits with places, population and footfall, and the site selection page covers the whole choice.
Mistakes that skew the answer
- Measuring each address on a different day. A rainy Tuesday against a dry Thursday is a weather comparison.
- Using different road distances. A 1 km ring around one site and the adjacent roads around the other will never match.
- Stopping after one week that contained a public holiday or a big event.
- Reading the jam factor alone. A road whose free-flow speed is 30 km/h feels different from a fast road slowed to 30, even at the same congestion.
Questions
How many days of readings do I need?
Ten working days at the hours that matter usually show a steady pattern. Add weekend readings if your customers come on Saturdays.
Can I compare more than two places?
Yes. The same flow measures every address in the list in one run, and Compare sites takes up to three spots for a quick look.
Does Traffic Flow give car counts?
No. It gives live speeds, the free-flow speed, congestion and the jam factor. Hourly car counts exist only for roads in the United Arab Emirates, in Regional data.
What if one place has no roads measured?
It says No roads measured and its numbers stay empty. Widen the road distance to 500 m or 1 km, or check that the address sits where you think it does.