Self storage site selection: dense homes, small flats and an easy drive in
Self storage site selection rests on four checks: how tightly people live, how small their homes are, how easily a van gets in, and the facilities already nearby.
Part of the guide AI employee for site selection
Good self storage site selection starts with where people run out of room at home: neighbourhoods with many residents per square kilometre, a lot of small flats, and frequent moves. Then it checks that a car or a hired van can reach the unit within a short drive on roads that are not jammed, and counts the storage facilities already serving the same drivers. A site that scores well on all four is worth a viewing; one that fails on access rarely recovers, however dense the homes around it.
This article is for operators, developers and investors looking at a new storage building or a conversion. It covers why storage demand behaves differently from shop demand, the four checks and the data behind each, a made-up comparison of two plots, the mistakes that leave units empty, and how an AI employee in xMap Flows can score candidate plots every month.
Why storage is a driving business, not a walking one
Almost nobody carries a sofa to a storage unit on foot. Customers arrive by car, van or a removals truck, often on a weekend, sometimes after work. So the catchment is a drive, usually a short one: people will pass one facility to reach a cheaper or newer one, but they will not cross a city for it. Think of the trade area as the homes within a 10 or 15 minute drive, drawn along real roads rather than as a circle.
Demand also comes from life events rather than from passing trade: moving house, a new baby, a renovation, a student leaving for the summer, a small business with stock but no warehouse. Places where those events are common, and where homes have no garage or loft, produce steady demand. Business renters such as online sellers and tradespeople add a second layer on weekdays.
The four checks
| Check | What to look at | Where it comes from |
|---|---|---|
| Dense homes | Residents and people per km2 inside the drive area | Demographics, where population figures exist |
| Small homes | Floor area of flats listed for rent or sale nearby | Property listings, in the United States, Japan and the UAE |
| Road access | Live speed and jam factor on the roads at the gate, and what a 10 minute drive reaches | Traffic Flow and Travel area |
| Rival facilities | How many storage sites, how close, how well rated, chain or not | Nearby places, type Self-storage facility |
What each check measures and which part of xMap Flows reads it.
Dense homes. The Demographics block counts residents inside an area and gives people per km2. Population figures exist only in some countries, among them France, Canada, India, Thailand, Egypt and Australia, and not the United Kingdom or the United States. Where they are missing, use your own census extract as a table in My data.
Small homes. Where property listings are covered, the floor area of the flats around a plot is a good proxy for how cramped homes are. A district where most listings are studios and one-bedroom flats under 50 m2 is a storage district. Read listings as what is advertised this week, not as the whole housing stock.
Road access. A gate on a road that is jammed every evening loses the after-work customer. Traffic Flow measures the live speed against the free-flow speed and gives a jam factor from 0 to 10; it does not count cars, so run it at the hours your customers come, such as Saturday morning and 6 pm on a weekday. Check the entrance too: a left turn across two lanes of traffic, or no room for a van to wait, is something only a site visit shows.
Rival facilities. xMap's places database has a type for self-storage facilities and another for moving and storage services. Count both inside the drive area, note their ratings and how many reviews they have, and see which belong to a chain.
A worked example, made up
Say an operator in Toronto is weighing two plots. Plot A sits beside a ring of new apartment towers, on a street that turns off a main road. Plot B is a larger, cheaper industrial unit at the edge of a low-rise suburb with detached houses.
Inside a 10 minute drive, Plot A has far more residents per km2, and the homes are mostly flats without basements. Two storage facilities are already there, both well rated. Plot B has fewer people around it, many with garages, and one older facility rated below 4. Traffic at Plot A's gate runs close to free-flow speed on a Saturday but slows sharply at 6 pm; Plot B's road is clear at both times.
The operator's reading: Plot A has the stronger demand and the tougher rivals, and needs a design that makes weekday evening visits easy, such as long hours and drive-up units off the side street. Plot B is cheaper but would be selling space to people who already have some. The numbers in this example are invented; the point is the reasoning.
Mistakes that leave units empty
- Drawing a circle. A 3 km circle across a river or a motorway counts homes that cannot reach you in ten minutes. Use a drive area.
- Counting people, not homes that lack space. A dense area of large family houses with garages stores its own clutter.
- Ignoring the gate. A plot can sit near a fast road and still be hard to enter. Look at the turn in and the queue space.
- Treating every rival the same. A small, poorly rated site with no drive-up units is not the same threat as a new, well-rated one.
- Reading one week of listings as the market. Listings change daily; look at them over several months before deciding a district is full of small flats.
Doing it with an AI employee in xMap Flows
An AI employee can score every candidate plot the same way each month, so the shortlist stays current while you negotiate. The pillar guide on AI employees for site selection explains the idea in general; here is the flow for storage.
- Schedule: the first Monday of each month.
- My data: your candidate plots as a table, each with a name and an address.
- Travel area: 10 minutes by car around each plot, following the roads.
- Demographics: residents and people per km2 in each area, where the country is covered.
- Nearby places: self-storage facilities and moving and storage services in each area, counted.
- Traffic Flow: speed and jam factor at each plot, with the schedule set to an evening hour.
- xMap LLM: score each plot from 0 to 100 against your own rules, with a one-line reason.
- Sort and limit, then Make a report: a PDF of the plots, best first, with a map.
What lands in your inbox is one report: each plot with its residents, the storage sites around it and how they are rated, the road speed at the gate, a score and the reason for it. The Where to open next and Competitor density around each site templates are good starting points; change the type of place to storage and add the plots you are looking at.
Questions
What drive time should a self storage catchment use?
Most operators look at 10 to 15 minutes by car. Travel area in xMap Flows draws up to 15 minutes or 10 km by road for now, which covers the core of a storage trade area.
Can xMap Flows tell me how many households have no garage?
No. It gives residents and age groups where population figures exist, and the floor area of listed flats where listings are covered. Use those as signals and add your own housing data for the rest.
Does Traffic Flow count how many cars pass the site?
No. It measures live speed, free-flow speed and how jammed the roads are when the flow runs. Car counts by hour are available only for roads in the United Arab Emirates, through Regional data.
How do I count rival storage facilities?
Use Nearby places with the type Self-storage facility, and add Moving and storage service if removals firms with storage compete for your customers. Each result comes with its distance, rating, reviews and whether it belongs to a chain.
Templates that do this
Read next
More on site selection and expansion · Every article · Templates