How many people live around a motorway exit, and how to count them
A junction draws drivers from far away but residents from close by. How to count the people living within a short drive of an exit, and what that number cannot tell you.
Part of the guide Location intelligence automation
To count the people who live around a motorway exit, draw the area reachable in a few minutes' drive from the junction along the local roads, then add up the residents in that area from a population grid. A plain circle gives a rougher answer because the motorway itself, and the land beside it, often splits the neighbourhood in two.
This is for teams choosing a site for a warehouse, a fuel station, a drive-through, a gym or a trade counter near a junction, and for planners who need to know how many homes an exit serves. It explains what the resident count means, how to draw the area, a worked example, the traps, and how an AI employee can repeat the count for any list of exits.
Residents are not drivers
The number of people living near an exit says nothing about how many drive past it. A quiet junction in a dense suburb can serve tens of thousands of residents while carrying little through traffic, and a busy interchange in farmland can have very few homes nearby. For a site that relies on local customers or staff, residents matter. For one that relies on passing trade, you need a measure of the road.
Be careful with that second measure. Live road speeds and congestion show how busy and slow a road is at a moment, but not how many cars use it. Hourly car counts are available only for roads in the United Arab Emirates, through a regional dataset. Elsewhere, count residents honestly and treat passing trade as a separate question.
Drawing the area around a junction
- Start at the exit slip road, not the motorway. Put the point where the slip road meets the local road, so the area grows along streets people can use.
- Use a short drive. Five or ten minutes by car shows the homes that would treat the junction as their own. Wider areas start to overlap with the next exit.
- Check both sides. If there is no crossing nearby, the far side of the motorway may be outside the drive area even though it looks close on a map.
- Add up residents inside it. A population grid of small hexagons, each about 0.1 square kilometres, gives the total, men and women and age groups.
A worked example: two exits near Toronto
The numbers here are made up to show the method. A logistics firm is weighing two junctions on the outskirts of Toronto for a small cross-dock where it wants to hire local staff.
| Within a 10-minute drive | Exit north | Exit east |
|---|---|---|
| Residents | 58,000 | 142,000 |
| Aged 20 to 59 | 31,000 | 80,000 |
| Warehouses already nearby | 14 | 36 |
Made-up figures for illustration only.
The east exit has far more working-age residents, which helps hiring, but it also has many more warehouses competing for the same people. The north exit has fewer residents and fewer rivals for staff. Neither figure says which junction carries more lorries; the firm would check its own delivery routes for that.
Traps that skew the count
- Counting by circle. A 3 km circle across a motorway and a river can double the residents compared with the homes that can really reach the exit.
- Areas that overlap. Two exits a few kilometres apart share residents. Do not add their totals together as if they were separate markets.
- Night and day. A population grid counts where people live. A business park full of workers by day can show very few residents.
- Mixing countries. Comparing an exit in a covered country with one in an uncovered country leaves a gap, not a zero.
How to do it with an AI employee
In xMap Flows an AI employee can measure every exit on your shortlist the same way. The blocks, in order:
- My data: your list of exits, each with the position where the slip road meets the local road.
- Travel area: a 10-minute drive from each exit.
- Demographics: residents, age groups and people per square kilometre inside each area.
- Nearby places: the businesses you would compete with or serve inside each area.
- Sort and limit: ranks the exits by the measure you care about.
- Email: the table to your team.
What you receive is one row per exit: residents, working-age residents, the share of children and seniors, and the count of competitors in the same drive area, ranked. Add Traffic Flow to see how fast the roads around each exit are moving right now. The template Warehouse sites near the motorway and the people follows this pattern.
Questions
Can I count the cars that use an exit?
Not in most countries. Traffic Flow gives live speeds and how congested roads are, never car counts. Hourly car counts are available only for roads in the United Arab Emirates through Regional data.
How long a drive should I use?
Five to ten minutes shows the homes that treat the junction as theirs. Travel area reaches up to 15 minutes or 10 km by road for now.
Why is the far side of the motorway missing from my area?
Because the area follows roads. If there is no crossing nearby, those homes cannot reach the exit quickly, so they are left out.
Does it work for exits in the United States?
Places and roads, yes. Resident counts, not yet: population data does not cover the United States or the United Kingdom.
Templates that do this
Read next
More on population and demographics · Every article · Templates