Ambulance response road speed: watching the roads into each hospital
How an ambulance service can read live speeds and the jam factor on the roads into its hospitals, compare approaches, and brief crews before the evening peak.
Part of the guide Location intelligence automation
Ambulance response road speed is the speed of the traffic an ambulance has to move through: on the feeder roads out of a district, and on the last approach into the emergency department. Live traffic data gives that speed for each road around a point, next to the speed the same road allows when it is empty, and a jam factor from 0 (free) to 10 (standstill or closed). A dispatch team that checks those figures on the approaches to its hospitals every 15 minutes can see which way in is slowing, before a crew is already stuck in it.
This piece is written for ambulance service planners, control room leads and private patient transport operators who send crews to more than one hospital. It is not the hospital estates view of its own front door. It covers which readings to watch, how to compare two or three hospitals at once, a made-up evening in Melbourne, the limits of the data, and an AI employee that keeps the board current.
The three readings worth watching
The Traffic Flow block returns many fields for each point. For an ambulance service, three carry most of the meaning.
- Congestion as a percentage. How much slower than free flow the roads are moving. A road that normally flows at 50 km/h and now moves at 20 km/h is 60% congested. It reads the same on a ring road and a side street, so approaches can be compared fairly.
- The jam factor. The 0 to 10 scale, also given in words: Free flowing, Light, Moderate, Heavy, Standstill. Heavy and Standstill are the levels where a crew under lights still loses time, because other drivers have nowhere to pull over.
- Roads closed. How many measured road stretches around the point are closed right now. One closed stretch on the only approach to a bay matters more than any speed.
Each point also carries the busiest road, the name of the stretch with the highest jam factor. That is the line a dispatcher reads aloud to a crew: not a score, but a street to avoid.
Comparing hospitals, not just watching one
When two emergency departments are a similar distance from a call, the one with the clearer approach is often the better choice. To make that comparison, put a point on each approach to each hospital: the last junction on every main road in, and the turn into the ambulance entrance. Keep the points at least 300 m apart, because points closer than that share one measurement.
Store those points in a table in My data with a column for the hospital and a column for the approach, such as north or ring road. Every run then gives a small grid: hospital by approach, each with its speed, congestion and level. A control room can sort it to see, at a glance, which hospital has every approach at Light or better.
A made-up evening in Melbourne
Say a patient transport company serves three hospitals in Melbourne and keeps eight approach points for them. This example is invented to show how the readings are used, not measured.
| Approach (example) | Speed now | Free flow | Level |
|---|---|---|---|
| Hospital A, northern road | 14 km/h | 48 km/h | Heavy |
| Hospital A, bay turn | 9 km/h | 22 km/h | Moderate |
| Hospital B, eastern road | 39 km/h | 52 km/h | Light |
| Hospital C, ring road | 61 km/h | 70 km/h | Free flowing |
Invented readings for illustration. Real runs give these fields for every point, measured when the flow runs.
At 5:40 pm the board shows Hospital A's northern road at Heavy, and the busiest road is named as the arterial that feeds it. For a non-urgent transfer that could go to A or B, the dispatcher chooses B. For a stroke patient who must go to A, the crew is told to use the eastern approach instead. Nobody had to phone around.
What this data cannot tell you
- It does not count vehicles. Traffic Flow gives speeds and the jam factor, never car numbers.
- It does not measure the ambulance. A vehicle with lights on moves differently from the traffic around it, so the readings describe the conditions it meets, not its journey time.
- It has no direction split. On a two-way road the slow traffic could be heading out, not in.
- It is live, not historic. To learn what Tuesdays at 6 pm usually look like, keep every reading in a sheet and look back after a few weeks.
Pair speeds with your own logged response times only as a guide. A slow week on the approaches is a reason to ask questions, not proof of why a response ran late.
An AI employee that keeps the board current
An AI employee can run the whole check through the evening peak and report only when it matters.
- Schedule every 15 minutes, with active hours between 4 pm and 8 pm on weekdays.
- My data brings in the table of approach points.
- Traffic Flow measures each point.
- Traffic incidents, set to around each incoming place, adds the nearest closure or roadworks within 1 km.
- Branch on a jam factor of 7 or more, or any closed road.
- Yes side: a message to the control room channel naming the hospital, the approach and the busiest road. Both sides: a row added to a sheet, so the history builds up.
The Where to stage ambulances in the evening peak template is a good start for the staging side, and Road closures near hospitals each morning covers the closures. Field operations teams who want more of this pattern will find it in the guide to AI employees for field operations.
Questions
Can live traffic data tell me how long an ambulance will take?
Not directly. It gives the speed and jam level of the traffic on each road, which is what an ambulance has to move through, but not the ambulance's own speed or a journey time.
How often should the roads be checked?
During the peak, every 15 minutes is a sensible rhythm. Outside it, every hour or once in the morning is usually enough.
Does it show which hospital approaches are closed?
Yes. Each point says how many measured road stretches around it are closed now, and Traffic incidents can add the nearest closure or roadworks to each point.
Can I see traffic history for an approach?
Traffic Flow is live. Add each reading to a sheet on every run and you build your own history; car counts by hour since 2021 exist only for roads in the United Arab Emirates.