Ships arriving at port today: a morning list and a live alert at the entrance
Terminal planners need two things: who is expected today, and the moment each ship actually comes in. How to get both from live AIS, with a zone drawn at the port entrance.
Part of the guide Workflow automation
Knowing the ships arriving at port today takes two different views. One is a list each morning of the vessels heading your way, read from what their crews broadcast about destination and arrival time. The other is a message the moment a ship actually crosses the port entrance, because published arrival times slip. Live AIS, the position signal ships send, gives you both, and a zone drawn across the entrance turns a stream of positions into a short list of arrivals.
This is for terminal and berth planners, stevedoring companies, port service firms (pilots, tugs, mooring gangs, chandlers, waste collection) and the logistics teams waiting on cargo. It explains what AIS can and cannot tell you, then builds both views.
What AIS gives you
The Ships (AIS) block listens to the live AIS stream for 30, 60 or 90 seconds over an area you draw, such as the port and its approaches, or around a point. For each ship heard it keeps the last position with its name, MMSI and IMO numbers, type (cargo, tanker, passenger and so on), speed, course, status such as under way or at anchor, its destination and ETA as entered by the crew, and its length and draught when heard.
View one: the morning list
Ships bound for your port usually say so in their destination field long before they arrive. Listen over a wide area of approaches, keep only ships whose destination mentions your port, and you have a rough list of who is coming. Typical spellings vary, so give the Filter several: for Santos you might accept SANTOS, BRSSZ and SSZ.
- Schedule: every day at 05:30.
- Area of interest: a shape drawn over the approaches, wide enough to catch ships a few hours out.
- Ships (AIS): listen 90 seconds, so slower-reporting ships at anchor are heard too; keep cargo, tanker and passenger.
- Filter: destination contains any of your port's spellings.
- Sort and limit by ETA, earliest first.
- Email to the planners: each ship with its type, length, draught, status and stated ETA.
Treat the list as an indication, not a schedule. A ship already at anchor outside may have an ETA from last week; one that has not updated its destination will be missing. The planners compare it with the agents' notices and the port's own line-up.
View two: the alert at the entrance
For the moment of arrival, draw the entrance itself: the breakwater gap, the channel mouth or the line at the pilot boarding point. Zone alert remembers where each ship was at the last run and lets through only those that entered the zone since then. If a ship went straight through between two runs, the straight line from its last position catches it as crossed.
- Schedule: every 15 minutes.
- Area of interest: the port and the outer anchorage.
- Ships (AIS): listen 60 seconds, moving ships only (over 1 knot).
- Zone alert: the entrance drawn on its own map, report Entered or crossed it.
- xMap LLM: one line per ship saying what it is, how long and how deep, and where it says it came from.
- A Slack or WhatsApp message to the duty planner and the mooring gang leader.
A night might bring: "02:15, NORDIC TERN, cargo, 183 m, draught 9.8 m, entered the channel at 11 knots." The mooring gang gets twenty more minutes of warning than a phone call from the bridge would give, and the planner sees the berth sequence change as it happens.
Mistakes to avoid
- A zone too small for the interval. A fast ferry can pass a narrow line between two 15-minute runs. Crossing detection helps, but draw the entrance generously.
- Listening too briefly at anchor. Ships at anchor report every few minutes. For the morning list, use 90 seconds.
- Taking ETA as fact. It is what the crew typed. Use it to sort, never to promise a customer a time.
- Forgetting tugs and pilots. Keep only the types you care about, or service craft will fill the alerts.
Templates to start from
Ships entering my zone is the alert above, ready to point at your port. Ships approaching the pilot boarding area and Ships waiting at anchor, for the berth planner are the two most common variations. For more on running alerts like these as part of daily operations, see the field operations guide.
Questions
How accurate is the arrival time?
The ETA comes from the ship's own broadcast and is typed by the crew, so it can be out of date. The zone alert tells you the actual moment a ship enters, which is why most terminals use both.
Will every ship be heard?
Not always. Coverage depends on the AIS receivers near your port, and a ship that sends nothing during the listen is missed in that run. A longer listen and frequent runs reduce the gaps.
Can I watch a single berth instead of the entrance?
Yes. Draw the berth as the zone and choose Entered it for arrivals and Left it for departures, in one flow each or with a Branch.
Does it tell me which cargo a ship carries?
No. AIS gives the ship's type, size, draught, speed and stated destination, not its cargo or manifest.